Lower energy consumption of manufacturing machinery
Metsä Tissue upgraded one of its tissue paper machines at the Mänttä mill, reducing energy consumption per tonne of paper produced by approximately 15%, Metsä Group reported in September.
The machine’s production capacity increased by 15%. It is used to manufacture tissue paper products from fresh wood fibre, primarily for the domestic market. The Mänttä mill produces napkins, household towels, paper towels, handkerchiefs, industrial rolls, and greaseproof paper for baking and cooking. The paper mill has three tissue paper machines, one greaseproof paper machine, and 11 tissue converting lines.
Reducing carbon dioxide emissions in mills
Last year, Stora Enso announced plans to reduce carbon dioxide emissions at several production sites. In April, the company stated that at the Enocell pulp mill in Joensuu, eastern Finland, fossil fuels will be replaced with tar oil.
The mill will also begin producing unbleached pulp, which has a carbon footprint one-fifth smaller than that of bleached pulp.
Meanwhile, in May, the company announced it would renovate the chemical recovery line at the Kaukopää pulp mill in Imatra, eastern Finland. The renovation will improve energy efficiency and increase the proportion of biofuel used in place of fossil fuels.
In June, Stora Enso reported on a project to renovate the board machine dryers at the Ingerois mill, while simultaneously switching the energy source from natural gas to electricity. This has reduced the mill’s carbon dioxide emissions by approximately a fifth.
Raw material washing equipment will be upgraded at the Varkaus facility. This will allow for savings equal to the annual heating bill of approximately two thousand average detached houses heated by electricity.
The total value of these investments is more than 60 million euros.
Renewable polyurethane for footwear and textiles
South Korean company Dongsung Chemical and German company UPM Biochemicals are developing renewable polyurethane for footwear production for the Asian market. The results obtained will later be used in the manufacturing of automotive interiors and adhesives (adhesion is the intermolecular bond between surfaces of different solid or liquid substances in contact).
The product uses bio-based monoethylene glycol (MEG). It is estimated that compared to fossil-based MEG, Dongsung's renewable polyurethane will reduce carbon emissions by at least 70%. Production of bio-monoethylene glycol will begin at the end of 2023 in Leuna, eastern Germany. Planned investments are estimated at around 750 million euros.
Carbon emission reduction of 300,000 t
UPM's new combined heat and power plant in Dörpen, Germany, will reduce the company's carbon dioxide emissions by 300,000 t per year.
The plant, which was commissioned in the autumn of 2022, produces energy for the company and supplies the surplus to the national power grid. It helps stabilise the German energy system. UPM’s goal is to reduce carbon dioxide emissions by 65% by 2030.
Log driving makes a comeback
At the end of November, Stora Enso announced that it would resume log driving to transport timber to its mills after a 14-year hiatus.
The company explains that moving logs via waterways will reduce carbon dioxide emissions generated during transport by up to 75% compared to rail and road haulage.
Log driving is a traditional way to transport timber across lakes in eastern Finland. Because the timber remains in the water for some time, this method prevents the spread of bark beetles. The presence of logs also improves the environment for water-filtering microorganisms, similar to the process in biological water treatment plants at sawmills.
Wood replaces concrete at Rauma sawmill
New hybrid elements, which combine concrete with an LVL (laminated veneer lumber) component, enabled more environmentally friendly construction at the Metsä Fibre Rauma sawmill, which began operations in the autumn of 2022.
The sawmill is the first building to be constructed using these sandwich-like hybrid elements. They are installed in the same way as regular concrete wall elements. The wood component creates a carbon store, and thanks to the lighter weight of the element, costs are saved during both installation and transport.
These hybrid elements were manufactured by the company Lipa-Betoni Pieksämäki, in eastern Finland. The Metsä Fibre Rauma sawmill uses pine as its raw material; it is the largest investment (approx. 260 million euros) in a sawmill in Finland to date.



